[email protected]

DETAILED SPECIFICATIONS - WATER MAIN Section Page

Acceptable pipe barrel material is ductile iron or PVC unless specified otherwise in the special conditions. Minimum pipe barrel diameter shall be 8 for main line water main. All ductile iron pipe shall conform to AWWA C-151/ANSI A 21.51. Ductile iron pipe shall have a cement mortar lining and an internal seal coat in accordance with AWWA C- DUCTILE IRON PIPES & FITTINGSStandards & Specification Shin Nan ductile iron pipes and fittings for water and sewerage systems are manufactured according to EN 545 / EN 598 / EN 969 / ISO 2531 and under the quality control system of ISO 9001 for quality assurance. The standard nominal sizes DN of pipes

Ductile iron pipe and fittings for water application

The variety of ductile iron pipeline ranges by Saint-Gobain PAM includes coatings and joints that are adaptable to various geographical configurations and different types of environment. Saint-Gobain PAM's comprehensive pipeline solutions can withstand all the hazards of SECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS Standard Specifications Ductile Iron Pipe and Fittings Revised August 2014 33 11 00.15-3 9. AWWA C153 / ANSI A21.53 Ductile-Iron Compact Fittings, 3 NPS through 24 NPS and 54 NPS through 64 NPS, for Water Service Ductile iron water pipe and fittings will be accepted on the basis of the SECTION III:Water Main Materials SpecificationsNov 01, 2020 · Specifications and Procedures Ductile Iron Pipe H:\DEPTS\TECH\Specifications\Water Main Standard Specifications\Works in Progress\2019-12-16 Construction Manual Edits\Section I - General Information (Effective 11-1-2020).docx Page 37 DUCTILE IRON PIPE GENERAL SPECIFICATIONS 1.

San Antonio Water System Standard Specifications for

San Antonio Water System Standard Specifications for Construction 814-4 January 2021 item no. 814 ductile iron pipe.docx wrap around ductile iron water mains when installing service corporations. o. The required method is to wrap pipe tape around the pipe over the polywrap in the area to be tapped. p. Specifications - Charlotte PipeSpecifications:PDF:MS Word:Master Specification for Sanitary, Storm and Special Waste & Vent Systems:Plastic Pipe and Fittings Drainage System:Plastic Sewer Pipe:PVC Cell Core (Foam Core) Sewer Pipe PS 50/Sewer and Drain Series Cast Iron Soil Pipe:Edge HP Iron Hubless:Edge HP Iron Hub and Spigot:FlowGuard Gold® Hot and Cold Water Specifications McWane DuctileWater Pipe:ANSI/AWWA:C11O/A21.10:Fittings - Cast Iron:ANSI/AWWA:C153/A21.53:Fittings - Ductile Iron:ANSI/AWWA:C111/A21.11:Rubber - Gasket Joints:ANSI/AWWA:C115/A21.15:Flanged Pipe:ANSI/AWWA:C104/A21.4:Cement - Mortar Linings:ANSI/AWWA:C105/A21.5:Polyethylene Encasement for Ductile Iron Pipe:ASTM:A674:Polyethylene Encasement for Ductile Iron Pipe:

Stipulation of Standards & Requirements for Water

All water fittings such as pipes, pipe fittings, valves, taps/mixers, urinal flush valves, flush valves for WCs, dual-flush low capacity flushing cisterns, materials, etc. for use in potable water service installations in Singapore shall comply with the standards and requirements Technical Specifications for Ductile Iron Pipes and FittingsPipes:Pipes shall conform to BS EN 545:2010; wall thickness shall be class C40 for the sizes DN 80mm to DN 400mm, class C30 for the sizes DN 450mm to DN 600mm and class C25 for the sizes DN 700mm to DN 2000mm. Suitable for push-on (flexible) jointing in standard lengths of 5.5m. Pipes over DN 2000mm will be class K9 unless otherwise specified. WATER & SEWER PIPE STANDARDS - Orrvillecement lined ductile iron pipe or approved plastic pipe as specified in Table 2. All water mains to be maintained by the City shall be Class 52 cement lined ductile iron pipe and fittings shall be a minimum of eight (8) inches in diameter. 11. All PVC water pipes and fittings must be accompanied by a manufacturer certificate that the pipe and

Ductile Iron Pipe Standards and Suggested Specifications

ANSI/AWWA C151/A21.51 American National Standard for Ductile-Iron Pipe, Centrifugally Cast, for Water; ANSI/AWWA C153/A21.53 American National Standard for Ductile-Iron Compact Fittings, 3-inch through 24-inch and 54-inch through 64-inch, for Water Service