[email protected]

Brass C36000 - Brass Rods, Brass Bars - Seeger Metals and

Blue Dot C36000 brass rod has the highest machinability of any brass alloy and offers machining accuracy with desired mechanical corrosion properties and a superior finish. C360 comes in round, hexagon, square, and rectangle brass rods and brass bars. Brass Grades Available for CNC Machining - Parts BadgerBrass. When copper is primarily alloyed with zinc it is refereed to as brass. The zinc content can vary but it is typically kept under 15% to maintain corrosion resistance in the alloy. Lead is also added in smaller quantities to increase machinability. Brass is known to be strong, machinable, conductive and corrosion resistant. Common brasses

C36000 (Free-Cutting Brass) - National Bronze

C36000 (Free-Cutting Brass) Chemical Composition (%max., unless shown as range or min.) Cu Fe Pb Zn Min./Max.60.0-63.0.352.5-3.0Rem. Nominal 61.5 - 2.7 35.4 Note:Cu + Sum of Named Elements, 99.5% min. Mechanical Properties (measured at room temperature, 68 F (20 C) Temper SectionCold Size Work Typ/ Min Temp Tensile Strength Yield Strength C36000 - Finkelstein Metals Finkelstein MetalsC-36000 Chemical Composition (%max, unless shown as range or min) Cu Fe Pb Zn Min/Max 60.0-63.0 0.35 2.5-3.7 Rem Note:Cu + Sum of Named Elements, 99.5% min. Applicable Specifications * Bar, Rod, Shapes - ASTM B16; SAE J461, SAE J463 Fabrication Processes * Machining * Roll Threading and Knurling Fabrication Properties Joining Technique Suitability Soldering Excellent Brazing Good C36000 Brass vs. C37700 Brass ::MakeItFromMay 30, 2020 · Both C36000 brass and C37700 brass are copper alloys. They have a very high 97% of their average alloy composition in common. There are 29 material properties with values for both materials. Properties with values for just one material (1, in this case) are not shown.

C36000 Brass- Brinell Hardness - Metal and Metallurgy

Sep 11, 2008 · ASM HANDBOOK Volume 2 has hardness data (Rockwell B, HRB)for half-hard C36000. Some typical values for rod range from 75-80 HRB. Table 4 of ASTM E 140 shows approximate hardness conversions for cartridge brass (70Cu-30Zn) as follows:75 HRB ~ 121 HB 80 HRB ~ 131 HB copper also has the data from ASM HANDBOOK Volume 2. C36000 Free Cutting Brass - Colored Bars Atlas BronzeC36000 Free Cutting Brass Atlas carries C36000 Free Cutting Brass Rounds, Rectangle, Hex Bar & Squares. We carry a very large range of sizes and will cut the material to length. This alloy is ideally suited for high speed machining operations with its superior Copper & Brass Alloys RoHS Frequently Asked QuestionsCopper and brass alloys containing up to 4% lead (Pb) by weight remain compliant under the latest revision of the directive (RoHS III)as summarized in the amendment to Annex III published in May 2018 and shown in the excerpt below. The expiry date for the current renewal cycle is July 21, 2021, 2023 and 2024 depending on the product category.

Copper Alloy No. C360 Free Cutting Brass , ASTM B16 CDA 360

1300-1450 F or 700-800 C. Annealing temperature. 800-1100 F or 425-600 C. Machinability rating (Free Cutting Brass=100) 100. Suitability for being joined by:Soldering/Excellent. Brazing/Good. Oxyacetylene Welding/Not Recommended. Free-Cutting Brass, UNS C36000, H02 (Cold Drawn 25% Free-Cutting Brass, UNS C36000, H02 (Cold Drawn 25%) Temper 6 mm rod Categories:Metal; Nonferrous Metal; Copper Alloy; Brass. Material Notes:Fair to excellent corrosion resistance. Excellent machinability. Fabricated by machining, roll threading and knurling. What is 360 Brass & Brass 360 Properties, Uses 360 vs Apr 03, 2020 · 360 Brass, also known as Alloy 360 or C36000, is a soft, ductile metal and standard alloy mainly consists of copper and zinc, added a small amount of lead and other elements. What is 360 brass made of? The chemical composition of brass 360 is:61.5% copper, 35.5% zinc, 3% lead, up to 0.35% iron. Brass 360 Properties

C36000 Free Cutting Brass Bar / C360 Brass / Free

C36000 Brass is commonly known as "Free Cutting" or "Free Machining" Brass. With a machinability rating of 100 this material is the standard by which all other metals are measured by. The 2 phase structure of C360 tends to form broken chips instead of continous coils, which interfere with high speed machining. This brass alloy is suited for high speed machining.